Tina Linux DongshanPI-Nezha STU Test Report

Test Environment

Operating System Information

• Download Link: Link Password: qcw7
• Reference Installation Document: Link

Hardware Information

• DongshanPI-Nezha STU
• A microSD card
• A USB to UART Debugger (e.g., CH340, CH341, FT2232, etc.)

Installation Steps

Compiling SDK

After downloading, you can find the SDK under DongshanNezhaSTU-TinaV2.0-SDK. Merge and extract the SDK:

cat tina-d1-h.tar.bz2.* | tar -zxv

Compile and package:

source build/envsetup.sh
lunch
make -j$(nproc)
pack

Flashing Image

Use dd to flash the image to the SD card:

sudo dd if=tina_d1-h.img of=/dev/your/device bs=1M status=progress

Logging into the System

Log into the system via the onboard serial port.

Expected Results

The system should boot normally and allow login via the onboard serial port.

Actual Results

The system booted up normally and login via the onboard serial port is also successful.

Boot Log

Screen recording (From flashing image to login):

kmodloader done
[   21.737966] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[   21.745840] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[   21.753436] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[   21.801755] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[   21.811462] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B
[   24.528045] libphy: 4500000.eth: probed
[   24.552037] sunxi-gmac 4500000.eth eth0: eth0: Type(8) PHY ID 001cc916 at 0 IRQ poll (4500000.eth-0:00)
[   24.663487] br-lan: port 1(eth0) entered blocking state
[   24.669315] br-lan: port 1(eth0) entered disabled state
[   24.701700] device eth0 entered promiscuous mode
[   24.708268] br-lan: port 1(eth0) entered blocking state
[   24.714139] br-lan: port 1(eth0) entered forwarding state
Trying to connect to SWUpdate...
[   25.441810] br-lan: port 1(eth0) entered disabled state
[   25.978830] [SNDCODEC][sunxi_card_hw_params][620]:stream_flag: 0
[   35.681434] usb1-vbus: disabling
[  238.501416] HDMI cable is disconnected
[  242.101413] hdmi_hpd_sys_config_release
[  248.371415] HDMI cable is connected
[  249.291638] error: invalid cea_vic code:0
[  249.296230] [HDMI2 error]: sink do not support this mode:0



BusyBox v1.27.2 () built-in shell (ash)

 _____  _              __     _
|_   _||_| ___  _ _   |  |   |_| ___  _ _  _ _
  | |   _ |   ||   |  |  |__ | ||   || | ||_'_|
  | |  | || | || _ |  |_____||_||_|_||___||_,_|
  |_|  |_||_|_||_|_|  Tina is Based on OpenWrt!
 ----------------------------------------------
 Tina Linux (Neptune, 61CC0487)
 ----------------------------------------------
root@TinaLinux:/# uname -a
Linux TinaLinux 5.4.61 #5 PREEMPT Fri Jul 22 03:07:57 UTC 2022 riscv64 GNU/Linux
root@TinaLinux:/# lscpu
/bin/ash: lscpu: not found
root@TinaLinux:/# opkg --version
opkg version 0.1.8
root@TinaLinux:/# 

Test Criteria

Successful: The actual result matches the expected result.

Failed: The actual result does not match the expected result.

Test Conclusion

Test successful.